The potential exists to use ultrasonic shear velocity for real-time microstructure assessment of the quenching step in the heat treatment of L80 steel pipe. L80 steel samples were austenitised and subsequently cooled in different quench mediums (water, oil, heated oil, air and furnace) to produce microstructures ranging from primarily martensite to coarse ferrite/pearlite mixed structures. Following heat treatment, the samples were ultrasonically tested, tensile and hardness tested and metallographically examined. The shear wave velocity was observed to increase as the underlying microstructure of each sample changed from primarily martensite, to primarily bainite and finally to coarse ferrite + pearlite. The measured shear wave velocity exhibited an inverse linear dependence on both yield strength and microhardness.
API Specification 5-CT. Specification for casing and tubing, 9th ed. June 2011.
2.
FreitasV, AlburquerqueV, SilvaE, Nondestructive characterization of microstructures and determination of elastic properties in plain carbon steel using ultrasonic measurements. Mater Sci Eng A. 2010;527:4431–4437. doi: 10.1016/j.msea.2010.03.090
3.
GurCH, TuncerBO.Characterization of microstructural phases of steels. Mater Charact. 2005;55:160–166. doi: 10.1016/j.matchar.2005.05.002
4.
PapakadisE.Ultrasonic attenuation and velocity in three transformation products in steel. J Appl Phys. 1964;35:1474–1482. doi: 10.1063/1.1713652
5.
PalanisamyV, SolbergJK, SalbergB, Microstructure and mechanical properties of API 5CT L80 casing grade steel quenched from different temperatures. OMAE2012, July 1–6. Rio de Janerio: ASME; 2012.
6.
IPSCO Research Report. Development of CCT Diagram, API 5CT Grade L80, Project 226-06; 2006.
7.
KimS, JohnsonW.Elastic constants and internal friction of martensite steel, ferritic-pearlitic steel and α-iron. Mater Sci Eng A. 2007;452–453:633–639. doi: 10.1016/j.msea.2006.11.147
8.
CastagnedeB, SachseW, ThompsonM.Determination of the elastic constants of anisotropic materials via laser-generated ultrasound. Ultrasonics International Conference, Madrid, Spain;1989. p. 71–79.
9.
KubeCM.Elastic anisotropy of crystals. Adv Phys. 2016;6:095209. doi: 10.1063/1.4962996
10.
LaugierP, HaiatG.Ch. 2: Introduction to the physics of ultrasound. In: Bone quantitative ultrasound. New York City (NY): Springer; 2011.
11.
LaneC.The development of a 2D ultrasonic array inspection for single crystal turbine blades. New York City (NY): Springer Publishing; 2014. p. 13–39.
12.
RoseJ.Ultrasonic waves in solid media. Cambridge: Cambridge University Press; 1999.
13.
WiskelJB, KennedyJ, IveyDG, Ultrasonic velocity evaluation of three grades of heat treated steel. Cdn. Inst NDE Conf., Edmonton, Canada; 2015.
14.
KennedyJ.Ultrasonic evaluation of microstructure in pipe steels [M.Sc. Thesis]. University of Alberta; 2015.
15.
ASTM, E112-13. Standard test methods for determining average grain size; 2013.
16.
ASTM, E8m-04. Standard test method for tensile testing metallic materials; 2008.
17.
RossC.Mechanics of solids. Amsterdam: Elsevier Science; 1999.
18.
MarderAR, KraussG.The morphology of martensite in iron alloys. Met Trans.1971;2:2343–2357. doi: 10.1007/BF02814873
19.
BenscoterAO, BramfittBL.Ch. 2: Origin of microstructure. In: Metallographers guide: practice and procedures for irons and steels. Russell Township (OH): ASM International; 2001. p. 23–48.
20.
BramfittBL.Effects of composition, procesing and structure on properties of iron and steels. In: ASM handbook vol. 20: materials selection and design. Russell Township (OH): ASM International; 1997. p. 357–382.
21.
GrangeRA, HirbalCR, PorterLF.Hardness of tempered martensite in carbon and low-alloy steels. Met Trans A. 1977;8a:1775–1785. doi: 10.1007/BF02646882
22.
KaijalainenA, SuikkanenP, PorterDA.Effect of re-austenitization on the transformation texture inheritance. IOP Conf Series: Mat Sci Eng. 2015;82:1–5.
23.
RajendranV, JayakumarT, PalanichamyP, First Differential of temperature dependent ultrasonic parameters as an effecive tool for identifying precipitation reactions in a slow heat-treated 8090 Al-Li alloy. J Alloys Compd. 2008;464:150–156. doi: 10.1016/j.jallcom.2007.09.127
