Sage Journals: Discover world-class research

Abstract

Hydraulic electric motor-pump is an integrated hydraulic power unit, raising rotational speed will further increase its power density. However, gaseous cavitation at high speed is the primary problem to be solved. In the present study, a new but simple centrifugal pressurization structure that integrated with the hollow shaft of hydraulic electric motor-pump was proposed to increase the inlet pressure of conjugated straight-line internal gear pump, and then to suppress gaseous cavitation at high speed. The numerical simulation is the main means of this work to investigate the gaseous cavitation characteristics of high-speed hydraulic electric motor-pump. In addition, a common conjugated straight-line internal gear pump model was developed as a reference to evaluate the pressurization effect of centrifugal tubes in terms of gas volume fraction. The simulation results present that compared with the significant increase of the suction chamber pressure of conjugated straight-line internal gear pump due to increasing the inclined angle of centrifugal tubes, the blocking effect of its inside wall to the fluid flow can be ignored. Under the same gas volume fraction in rotating volume, the rotational speed of hydraulic electric motor-pump is much higher than conjugated straight-line internal gear pump due to the pressurization effect of centrifugal tubes. On the premise of no obvious gaseous cavitation of centrifugal tubes, the recommended speed of hydraulic electric motor-pump is up to 13,000 r/min.

Keywords

Hydraulic electric motor-pump conjugated straight-line internal gear pump high speed gaseous cavitation centrifugal pressurization

Get full access to this article

View all access options for this article.

References

Zhang

. Electric and hydraulic-hydraulic drive electric control, hydraulic drive electric drive and electric drive. Hydraul Pneum Seals 2020; 40: 1–6. (In Chinese).

Ranta

Laihanen

Karhunen

. The role of bioenergy in achieving the carbon neutrality target in Finland by 2035—a case study of student surveyed at University in Finland. J Sustain Bioenergy Syst 2021; 11: 61–81.

Yang

Pan

. Engineering research in fluid power: a review. J Zhejiang Univ Sci 2015; 16: 427–442.

Jeong

S-J

Hong

S-Y

Song

J-H

, et al. Establishment of cavitation inception speed judgment criteria by cavitation noise analysis for underwater vehicles. Proc Inst Mech Eng M: J Eng Mari Environ 2021; 235: 546–557.

Suo

Jiang

Wang

. Hydraulic axial plunger pump: gaseous and vaporous cavitation characteristics and optimization method. Eng Appl Comput Fluid Mech 2021; 15: 1. 712–726.

Roy

Maiti

Das

, et al. Estimations of leakages through gaps at ‘transition’ contacts using computational fluid dynamics and photoimaging of core-flow cavitation features in Gerotor pumps. Proc Inst Mech Eng E: J Process Mech Eng 2021; 235: 1748–1770.

Gamez-Montero

Castilla

Codina

. Methodology based on best practice rules to design a new-born trochoidal gear pump. ARCHIVE Proc Inst Mech Eng Part C J Mech Eng Sci 1989–1996 (Vols 203–210) 2017; 232: 095440621769735.

Rundo

Altare

Casoli

. Simulation of the filling capability in vane pumps. Energies 2019; 12: 1–18.

Kunkis

Weber

. Experimental and Numerical Assessment of an Axial Piston Pump's Speed Limit[C]// Bath/ASME 2016 Symposium on Fluid Power & Motion Control. Bath, UK. September 7–9, 2016. V001T01A048. ASME.

10.

Mingxue

Yang

Xiaoqing

, et al. Influence of suction pressure on cavitation characteristics of external gear pump. Trans Chinese Soc Agricultur Machin 2019; 50: 420–426.

11.

Chao

Zhang

, et al. Effects of inclined cylinder ports on gaseous cavitation of high-speed electro-hydrostatic actuator pumps: a numerical study. Eng Appl Comput Fluid Mech 2019; 13: 245–253.

12.

Song

Chen

Zhou

. Investigation of fluid delivery and trapped volume performances of Truninger gear pump by a discretization approach. Adv Mech Eng 2016; 8: 1–15.

13.

Chen

Liao

. Design and analysis of conjugated straight-line internal gear pairs. Int J Prec Eng Manuf 2021; 22: 1425–1440.

14.

Stewart

. Centrifugal pumps. Surface Production Operations 2019; 6: 61–309.

15.

Antoniak

Stryczek

. Visualization study of the flow processes and phenomena in the external gear pump. Arch Civ Mech Eng 2018; 18: 1103–1115.

16.

Burlon

Micheli

Simonato

, et al. Experimental analysis of the influence of polymer solutions on performances and cavitation of small size pumps for professional appliances. Proc Inst Mech Eng, Part E: J Process Mech Eng 2021; 235: 3–11.

17.

Wang

Cheng

, et al. Experimental investigation of cavity length pulsation characteristics of jet pumps during limited operation stage. Energy 2018; 163: 61–73.

18.

Chai

Yang

, et al. Research on flow characteristics of straight line conjugate internal meshing gear pump. Processes 2020; 8: 269.

19.

Frosina

Senatore

Buono

, et al. A Three-Dimensional CFD Methodology to Study Vane-Ring and Vane-Under-Vane Interactions of a Vane Pump Power Split Transmission[C]// In 9th FPNI PhD Symposium on Fluid Power, FPNI 2016. American Society of Mechanical Engineers.

20.

Ding

Visser F

Jiang

, et al. Demonstration and Validation of a 3D CFD Simulation Tool Predicting Pump Performance and Cavitation for Industrial Applications[C]// Proceedings of the ASME 2009 Fluids Engineering Division Summer Meeting. Volume 1: Symposia, Parts A, B and C. Vail, Colorado, USA. August 2–6, 2009. pp. 277–293. ASME.

Supplementary Material

Please find the following supplemental material available below.

For Open Access articles published under a Creative Commons License, all supplemental material carries the same license as the article it is associated with.

For non-Open Access articles published, all supplemental material carries a non-exclusive license, and permission requests for re-use of supplemental material or any part of supplemental material shall be sent directly to the copyright owner as specified in the copyright notice associated with the article.

0.00 MB

0.85 MB