The exergy analysis and air pollutants emission estimation from the kiln system of a major cement manufacturing plant located in Nigeria were conducted with a view to improve the level of performance of the production unit and minimize environmental effects. Material balance and exergy analysis were carried out on the system to determine the exergetic efficiency and exergy destruction rate. Pollutants emission was estimated using bottom-up emission factor approach. The physical and chemical exergy output obtained were 9.07×107 and 1.46×08 kJ/h, respectively. The exergy efficiency of the kiln system was 27.35%. The measure of entropy generation (6.53×108 kJ/h) represented a huge potential for energy savings for the unit. CO2 emission represented about 99.04% of the total criteria air pollutants emission from the kiln and an estimate of 0.90 tonnes of CO2/tonne of clinker produced was obtained. To improve the exergy efficiency and reduce pollutants emission from the kiln system, possible heat recovery options and CO2 mitigation approaches were suggested.
MadeleineR.Emissions from the Cement Industry. Columbia:
Earth Institute, Columbia University, 2012.
4.
XiFDavisSJCiaisPet al.
Substantial global carbon uptake by cement carbonation. Nat Geosci2016;
9: 880–883.
5.
SummerbellDLBarlowCYCullenJM.Potential reduction of carbon emissions by performance improvement: a cement industry case study. J Clean Prod2016;
135: 1327–1339.
6.
WorrellEPriceLMartinNet al.
Carbon dioxide emissions from the global cement industry.Annu Rev Energy Environ2001;
26: 303–329.
7.
Oni AO, Fadare DA and Adeboye LA Thermoeconomic and environmental analyses of a dry process cement manufacturing in Nigeria. Energy 2017; 135: 128–137.
HuntzingerDNEatmonTD.A life-cycle assessment of Portland cement manufacturing: comparing the traditional process with alternative technologies. J Clean Prod2009;
17: 668–675.
10.
AliMSaidurRHossainM.A review on emission analysis in cement industries. Renew Sustain Energy Rev2011;
15: 2252–2261.
11.
VatopoulosKTzimasE.Assessment of CO2 capture technologies in cement manufacturing process. J Clean Prod2012;
32: 251–261.
12.
HasanbeigiAPriceLLinE.Emerging energy-efficiency and CO2 emission-reduction technologies for cement and concrete production: a technical review. Renew Sustain Energy Rev2012;
16: 6220–6238.
13.
BenhelalEZahediGShamsaeiEet al.
Global strategies and potentials to curb CO2 emissions in cement industry. J Clean Prod2013;
51: 142–161.
14.
RostamiVShaoYBoydAJ.Durability of concrete pipes subjected to combined steam and carbonation curing. Construct Build Mater2011;
25: 3345–3355.
15.
LagerbladB.Carbon dioxide uptake during concrete life cycle – state of the art.
Stockholm:
Swedish Cement and Concrete Research Institute CBI, 2005.
16.
ÇamdaliÜEri̇şenAÇelenF.Energy and exergy analyses in a rotary burner with pre-calcinations in cement production. Energy Convers Manage2004;
45: 3017–3031.
17.
AltinkaynakMKabulAKizilkanÖ.Exergetic assessment of a rotary kiln for clinker production in cement industry. IJEX2015;
16: 263–277.
18.
MadloolNSaidurRRahimNet al.
An exergy analysis for cement industries: an overview. Renew Sustain Energy Rev2012;
16: 921–932.
19.
UtluZSogutZHepbasliAet al.
Energy and exergy analyses of a raw mill in a cement production. Appl Therm Eng2006;
26: 2479–2489.
20.
PeinadoDDe VegaMGarcía-HernandoNet al.
Energy and exergy analysis in an asphalt plant’s rotary dryer. Appl Therm Eng2011;
31: 1039–1049.
21.
GutiérrezASMartínezJBCVandecasteeleC.Energy and exergy assessments of a lime shaft kiln. Appl Therm Eng2013;
51: 273–280.
22.
CengelYABolesMA.Thermodynamics: an engineering approach. 5th ed.
New York, USA:
McGraw-Hill, 2006.
23.
GürtürkMOztopHF.Energy and exergy analysis of a rotary kiln used for plaster production. Appl Therm Eng2014;
67: 554–565.
24.
GreenDW.Perry’s chemical engineering handbook.New York, NY:
McGrawHill Professional Publ., 2007.
25.
BejanATsatsaronisG.Thermal design and optimization. New Jersey:
John Wiley & Sons, 1996.
HasanbeigiAMenkeCPriceL.The CO2 abatement cost curve for the Thailand cement industry. J Clean Prod2010;
18: 1509–1518.
28.
BarceloLKlineJ. The cement industry roadmap to reduce carbon emissions. In: Carbon management technology conference,7–9 February 2012, Orlando, USA
29.
WBCSD I.Cement Technology Roadmap 2009: carbon emissions reductions up to 2050. Geneva, Switzerland:
World Business Council for Sustainable Development and International Energy Agency. http://wbcsdcement org/pdf/technology/WBCSD-IEA_Cement% 20Roadmap pdf. 2009(accessed 23 July 2017).
30.
IEA. Energy technology transitions for industry: strategies for the next industrial revolution. Château de la Muette in Paris, France.:
OECD Publishing, 2009.
31.
Farag LM. Energy and exergy analyses of Egyptian cement kiln plant with complete kiln gas diversion through by Pass. International Journal of Advances in Applied Sciences 2012; 1: 35–44.
32.
Taylor HF. Cement chemistry. London: Thomas Telford Publishing, 1997
33.
Yilmazoglu MZ and Amirabedin E. 3E analysis of a solar assisted rotary type coal dryer. International Journal of Renewable Energy Research (IJRER) 2012; 2: 16–22.
34.
Kandilci H and Sarac H. Investigate energy efficiency by making exergy analysis in the cemen sector, international exergy. Energy and Environment Symposium, 14 July, 2013.
35.
Söğüt Z, Oktay Z, Karakoç H. Mathematical modeling of heat recovery from a rotary kiln. Applied Thermal Engineering 2010; 30: 817–825.
36.
Atmaca A and Yumrutaş R. Analysis of the parameters affecting energy consumption of a rotary kiln in cement industry. Applied Thermal Engineering 2014; 66: 435–444.
